893 reviews analysed
1. 2500W Induction Heating Board DC 12V ZVS Induction Heating Board Flyback Driver Heater DIY High Frequency Induction Heating Machine Module with Spiral Coil and Water Pump
- The heating board is made of PCB, with stable performance.
- The power cord is completely covered with copper cover, which can increase current and calorific value.
- Use the large power supply of the radiator for better cooling.
- The output terminals use three M4 copper columns in parallel to connect to other outputs, such as the FBT.
- 6 IRFP260 and 12 parallel resonant capacitors are used for high power and efficiency.
Condition: 100% brand new
Item Type: Induction Heating Board
Color: as picture shown
Pump input voltage: DC 12V
Input voltage: 12V-48V recommend 36 V
Power: 12 V: ≥ 10A, 15V: ≥ 20A
Maximum power: 2500W
Maximum current: 50A
1 x Induction Heating Board
1 x Spiral Tube
1 x Water Pump
2. 1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan
- The induction heating boards maximum power is 1800W, adopted super PCB layout design and super heat sink, heat dissipation good, since with a cooling fan interface, can also do Tesla discharge, generator voltage inverter, etc
- The induction heating circuit adopt 12-48V DC power supply, maximum current is 40A, the power uo to 1800W. It can work continuously under the condition of good heat dissipation. moderate power which make it can be used to quenching, annealing and other heat treatment. also for melted with graphite crucible kim/silver/ copper/aluminum and so on, heating is evenly and fast
- it is recommended that not exceed 48V 35A to prevent accidents and damage,Although withstand more than 40A current.Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small almost without response, and 12V power might lead to the voltage decreases, which is very dangerous.More than 24V/20A power supply, the greater the voltage/current, the greater the heating power, heating faster.
- please check the power output meets the requirements if the MOS tube fever,and be sure to do a good job of cooling.Do not empty the board, otherwise it will create a very high noise, then MOS tube will burn out
- please do not to heat too large metal, otherwise it may be overloaded, please add a 35A fuse or ammeter and air switch for better use (not included).
Product size:Approx.180x90x80mm (please allowed 1-3mm error)
Heater ring inner:70mm (Recommended crucible+quartz suit,maximum support of 58mm crucible)
New style :AC 100-220V Adapter
Old style: Main board Input voltage: 12V-48V recommend: 36V above
Power requirements: less than 12V≥10A , 15V above≥15A
NOTE:New style and Old style shipped by randomly!!!
It doesn’t affect the performance of product.!!!
Maximum power: 1800W
Maximum current: 40A
1 x PCB board
1 x 48V copper tube
1.The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. you can buy a small water pump and 2 meters of rubber hose(inner diameter is 4mm) for build a water cooling system
Please pay attention to using switch power supply, because output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit that will be lead to circuit can’t afford to vibrate caused by lacking voltage,so that the two MOS tube conduction and components will burned
comes with heating circle diameter-60 mm/design voltage-36V,if you use more than 40V Devices shall be used ≥70 mm diameter heating ring, DC 12V water pump use, please use separate power supply voltage regulator module to avoid fan and water pump are burn out
The minimum input is 12V, but it doesn’t mean all 12V power supply available,The module has specific requirements on voltage and current , 12V require current must than 10A ,output power will greatly reduced if the power is too low ,which will lead to two MOS conduction at the same time & burn MOS tube when lower than 12V
3. AEEDAIRY Low ZVS 12-48V 20A 1000W Low Voltage Induction Heating Board High Frequency Induction Heating Machine Module
4. CGOLDENWALL 25KW High Frequency Induction Heater Furnace Heating Melting Furnace System 30-80KHz
Description and Advantages:
1. Adopts the latest MOSPET, IGBT power units and frequency conversion control techniques with high efficiency, low energy consumption and higher output power
2. With constant current and constant power control function to greatly optimize the heating process of metals, realize efficient and fast heating, and fully exert the superiority of the products
3. Power consumption is half of traditional electron tube high frequency induction heating equipments under same conditions
4. With 100% load design, can work in 24 hours without stop. Infrared temperature detector can be equipped to realize the automatic control of temperature, improve heating quality and simplify manual operation
5. With heating-insulating-cooling three stages function setting, the heating and insulating time required can be get to accommodate to the batched and repeated heating situations
6. With multiple status display of overflow, overvoltage, low water, phase failure and load malfunction, providing higher reliability and sustainability
7. Select power supply according to the power and frequency. The higher the frequency, the shallower the heating depth, and the lower the frequency, the better the diathermancy.
Shipping Tips & Attention:
1. The machine comes with 4 pcs of heating coils for free. Please contact us if you want to order more or other dimension heating coils.
2. This machine can't be used with a plug directly, it needs a wire to connect the machine to power line directly (the cross-sectional area of power line must be larger than 6 square milimeters.)
3. Please contact us for the English user manual if you need it.
5. 15KW 30-100KHz High Frequency Induction Heater Furnace 2200 ℃ (3992 ℉) High Frequency Machine (220V heater)
- [Basic Information]: Output power: 15 KW Output current: 200 – 600 A , Fluctuating frequency: 30 – 100 KHZ , Heating time: 1-99 s (auto) , Input voltage: Single phase 220v , Flow rate of cooling water: 0.06-0.12Mpa, 7.5 L / min Water temperature protection point: 40 ℃ (104 ℉) , Max. heating temperature: 2200 ℃ (3992 ℉) , Load duration: 100% , Cooling: Water cooling.
- [Advantage]: With constant current and constant power control function to greatly optimize the heating process of metals, realize efficient and fast heating, and fully exert the superiority of the products
- Power consumption is half of traditional electron tube high frequency induction heating equipment under same conditions
- With 100% load design, can work in 24 hours without stop. Infrared temperature detector can be equipped to realize the automatic control of temperature.
- [Application]: Do heat treatment for gear wheel and axis
- Continuous annealing for steel wire
- Heating and hot press molding for dishware
- Forging & molding for standard work-piece.
- [Package Include]: 1 x 15 KW High Frequency Induction Heater Furnace , 2 x Heating Coils, 1 x Foot Switch, 1 x English Manual, 1x Dry Pot
- [Warranty]: We provide 1 year warranty for the machine and after-sales service for all life.
With heating-insulating-cooling three stages function setting, the heating and insulating time required can be get to accommodate to the batched and repeated heating situations; With multiple status display of overflow, over-voltage, low water, phase failure and load malfunction, providing higher reliability and sustainability.
6. Seajunn Low ZVS 12-48V 20A 1000W Low Voltage Induction Heating Board High Frequency Induction Heating Machine Module
By our suggestions above, we hope that you can found High Frequency Induction Heating for you.Please don’t forget to share your experience by comment in this post. Thank you!